Driver sd needs updating please use bustype methods gentoo

Driver sd needs updating please use bustype methods gentoo

As the message says my boot is taking about 10 minutes, of which 95% of the time is spent trying to recognize ata4 device.I'm using the x86_64 version of arch, which works just fine on my laptop, and on my desktop - when it boots that is.I don't have a RAID I think, it's marked as IDE in my bios, but I do seem to be using the jmicron technology.I haven't selected anything while doing the installation, and I'm not sure if I should have?I've bought a new PATA cable, even tried meddling with master/slave pins on the hard disk, tried booting it as only device, but alas to no avail.I've also put the LBA mark on it in bios, it did nothing.I'm running out of ideas, can anyone please suggest something - obviously not buying a new HD, it's not worth it.

Memory: 2057296k/2096000k available (2958k kernel code, 38092k reserved, 1092k data, 248k init) SLUB: Genslabs=11, HWalign=64, Order=0-1, Min Objects=4, CPUs=4, Nodes=1 Calibrating delay using timer specific routine..A little update in hope someone out there might help out: I've been trying out other distros, notably slackware (x86 version), knoppix (didn't get it to boot properly, only one attempt though), gentoo (didn't get it to boot the installation cd, and since i couldn't get knoppix up i gave up on it temporarily).And of those I could get slackware to boot up without causing too much frustration to myself (LILO sucks).Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode.usb 4-1: new low speed USB device using uhci_hcd and address 3 usb 4-1: configuration #1 chosen from 1 choice rtc_cmos : rtc core: registered rtc_cmos as rtc0 rtc0: alarms up to one month r8169 Gigabit Ethernet driver 2.2LK loaded ACPI: PCI Interrupt 00.0[A] - IRQ 22 PCI: Setting latency timer of device 00:1b.0 to 64 hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...

driver sd needs updating please use bustype methods gentoo-53driver sd needs updating please use bustype methods gentoo-41driver sd needs updating please use bustype methods gentoo-71

Brought up 2 CPUs net_namespace: 120 bytes NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG at e0000000 - efffffff ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S1 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00) PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO PCI quirk: region 0480-04bf claimed by ICH6 GPIO PCI: Transparent bridge - 00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.

Join our conversation (3 Comments).
Click Here To Leave Your Comment Driver sd needs updating please use bustype methods gentoo.

Comments:

  1. 1
    Steve

    COM Get-Distribution Group -Result Size Unlimited | Set-Distribution Group -Bypass Security Group Manager Check -Managed By '[email protected] COM’ #Clear home MTA property for a single distribution group (If any distribution groups have this property set it can force a specific server to send distribution group messages) Get-Distribution Group | For Each 3.

  2. 1
    Steve

    For others it involves dirty voice calls which can lead to climax.

  3. 1
    Steve

    Featuring mobile chat rooms as well, helps you find and connect with single women and men throughout the globe.

  4. 1
    Steve

    The Seminary embraces in its life and work a rich racial and ethnic diversity and the breadth of communions represented in the worldwide church.

  5. 1
    Steve

    Welcome to our reviews of the elite matchmaking san diego (also known as make girlfriend online).

  6. 1
    Steve

    Try our forums and kick back, take things at your own pace, and enjoy.

Leave a Reply

Your email address will not be published. Required fields are marked *